← NSN Search
RESISTOR,VARIABLE,NONWIRE WOUND,
5905-01-234-0529NIIN 012340529USAEA · inactiveDEMIL ASOS SMSCatalog $6
FSC5905Resistors
Suppliers
2
DIBBS awards
0
Total value
—
Last award
—
Approved manufacturers
Qualified to supply per MCRL — no confirmed DIBBS award on record for this NSN. Each CAGE opens the manufacturer page.
00752L3HARRIS TECHNOLOGIES, INC.AMITYVILLE, NYSAM
PN 394823-11
81349MILITARY SPECIFICATIONSSAM
PN MIL-PRF-39035/3, MIL-R-39035/3, MILR39035-3, RJR26FX104M +3 more
Characteristics
FLIS item characteristics from PUB LOG identification.
| Characteristic | Value |
|---|---|
| ACTUATOR TRAVEL CONTROL FEATURE | CLUTCH |
| ACTUATOR TYPE | SINGLE SHAFT |
| AMBIENT TEMP IN DEG CELSIUS PER SECTION AT FULL RATED POWER | SINGLE SECTION 85.0 |
| AMBIENT TEMP IN DEG CELSIUS PER SECTION AT ZERO PERCENT RATED POWER | SINGLE SECTION 150.0 |
| BODY HEIGHT | INCHES NOMINAL 0.250 |
| BODY LENGTH | INCHES NOMINAL 0.250 |
| BODY WIDTH | INCHES NOMINAL 0.165 |
| CENTER TO CENTER DISTANCE BETWEEN CENTER TERMINAL AND OUTSIDE TERMINAL | INCHES NOMINAL 0.100 |
| CENTER TO CENTER DISTANCE BETWEEN TERMINAL ROWS | INCHES NOMINAL 0.100 |
| CENTER TO CENTER DISTANCE BETWEEN TERMINALS | INCHES NOMINAL 0.200 |
| CUBIC MEASURE | CUBIC INCHES 0.021 |
| EFFECTIVE ELECTRICAL ROTATION IN DEG ANGULAR ROTATION | MINIMUM 3600.0 AND MAXIMUM 9000.0 |
| ELECTRICAL RESISTANCE PER SECTION | KILOHMS SINGLE SECTION 100.000 |
| END ITEM IDENTIFICATION | 1190-01-189-7381 |
| FRAGILITY FACTOR | MODERATELY RUGGED |
| MAXIMUM RUNNING TORQUE | INCH-OUNCES 3.00 |
| MAXIMUM STARTING TORQUE | INCH-OUNCES 3.00 |
| MOUNTING METHOD | TERMINAL |
| OVERALL HEIGHT | INCHES NOMINAL 0.422 |
| OVERALL LENGTH | INCHES NOMINAL 0.300 |
| OVERALL WIDTH | INCHES NOMINAL 0.165 |
| POWER DISSIPATION RATING PER SECTION IN WATTS | FREE AIR SINGLE SECTION 0.25 |
| RELIABILITY FAILURE RATE LEVEL IN PERCENT | 0.010 |
| RELIABILITY INDICATOR | ESTABLISHED |
| RESISTANCE TOLERANCE PER SECTION IN PERCENT | SINGLE SECTION -10.0 TO 10.0 |
| SECTION QUANTITY | 1 |
| SHAFT BEARING TYPE | BEARING |
| SHAFT DIAMETER | INCHES NOMINAL 0.075 |
| SHAFT LENGTH | INCHES MAXIMUM 0.050 |
| SPECIFICATION/STANDARD DATA | GOVERNMENT SPECIFICATION 81349--IL-R-39035 TO 3 |
| TEMP COEFFICIENT OF RESISTANCE PER SECTION IN PPM PER DEG CELSIUS | SINGLE SECTION -100.0 TO 100.0 |
| TERMINAL LENGTH | INCHES MINIMUM 0.172 |
| TERMINAL LOCATION | LOWER ADJACENT SIDE TWO ROWS |
| TERMINAL TYPE AND QUANTITY | PIN 3 |
| TEST DATA DOCUMENT | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). 81349--IL-R-39035 |
Open buys
SPE7M126U5920
DIBBS · quotes by Sep 24, 2026 · UNRESTRICTED